Required courses, 35 hours

• BMEN 1300 - Discover Biomedical Engineering
• BMEN 1400 - Software for Biomedical Engineers
• BMEN 2210 - Biomedical Circuits and Data Acquisition Best Practices
• BMEN 2320 - Biomedical Instrumentation I
• BMEN 3310 - Engineering Measurements from Human Systems
• BMEN 3311 - Biomedical Signal Analysis
• BMEN 3312 - Introduction to Biomechanics
• BMEN 3321 - Biomaterials
• BMEN 3350 - Biomedical Transport Phenomena
• BMEN 4212 - Senior Design I
• BMEN 4222 - Senior Design II
• BMEN 4310 - Biomedical Modeling

Biomedical engineering electives, 9 hours

Three advanced, 4000-level, organized BMEN courses.

Additional engineering electives, 18 hours (minimum)

18 hours to fulfill one of five tracks:

• Biomedical instrumentation: 18 hours in BMEN or EENG courses
• Biomechanics: 18 hours in BMEN or MEEN courses
• Biocomputing: 18 hours in BMEN or CSCE courses
• Biotechnology: 18 hours in BIOC/BIOL
• Biomaterials: 18 hours in materials science and engineering
  

Foundation courses

BMEN foundation courses include BMEN 1300 , BMEN 1400 , BMEN 2210 , BMEN 2320 , MATH 1710 , TECM 2700 , PHYS 1710 , PHYS 1730 , MATH 1720 , ENGL 1310  or TECM 1700 , BIOL 2301 , BIOL 2311 , CHEM 1410  /CHEM 1430  or CHEM 1415  /CHEM 1435  .

Successful completion of foundation courses is based on achieving a C or higher in each course and cumulative GPA of 2.5.

Major transfer policy

Students enrolled at UNT can transfer into Biomedical Engineering if they have completed the following courses with a C or better and with a cumulative GPA of at least 2.5.

• BMEN 1300 - Discover Biomedical Engineering
• BMEN 1400 - Software for Biomedical Engineers
• ENGL 1310 - College Writing I
• MATH 1710 - Calculus I
• MATH 1720 - Calculus II
• TECM 1700 - Introduction to Professional, Science, and Technical Writing
• TECM 2700 - Technical Writing

Department policies

Policy on Academic Performance, Progression, and Dismissal in the College of Engineering

Students in the College of Engineering will conduct themselves in a professional manner in their interaction with their peers, faculty, staff and the community in general. A student may be dismissed from the college for inappropriate conduct (please refer to the Code of Student Conduct).

Each semester, students are required to take engineering foundation courses and/or prerequisites to the engineering foundation courses until all foundation courses are successfully completed. Successful completion is a 2.5 GPA for all engineering foundation courses with a C or better in each course.

Successful completion of the foundation courses is required for enrollment in all 3000 and 4000 level courses.

A minimum grade of C is required in all courses required in a student’s major for degree completion. Courses include, but are not limited to, engineering, computing, mathematics, laboratory sciences, supporting area, technical elective, technical option, energy elective, and specialization courses.

A minimum grade of C is required in all courses required in a student’s major for prerequisite completion. Courses include, but are not limited to, engineering, computing, mathematics, laboratory sciences, supporting area, technical elective, technical option, energy elective, and specialization courses.

A student making grades lower than C two times in the same course in any College of Engineering foundation course or in any course required by the major is subject to dismissal from the College of Engineering, pending a review by the Associate Dean for Undergraduate Studies in the College of Engineering.

A student must maintain good academic standing within the university. Please see “Academic status” and “Regulations governing students under academic suspension” in the Academics section of this catalog.”